PT Solutec Daya Mandiri-SDM

Fungsi Needle Valve dan aplikasi graphite untuk media steam (uap)

Fungsi Needle Valve dan Konstruksi body Fungsi Needle Valve Fungsi needle valve adalah yang terutama digunakan dalam sistem perpipaan untuk mengatur aliran fluida (Flow control) disamping itu juga dapat digunakan untuk menutup (sioalation).Secara fungsi pengoperasian dapat digerakkan secara manual atau dapat digerakkan secara otomatis oleh sinyal dari perangkat kontrol, atau katup dapat merespons perubahan kondisi …

Continue reading “Fungsi Needle Valve dan aplikasi graphite untuk media steam (uap)”

Leak of valve type and test

Leak of valve Introduction Leak of valve are a common problem in fluid systems. Technically speaking, it is impossible for systems to be 100% leak-free. However, in applications with a high degree of purity, even the smallest leak can affect the smooth operation of systems, meaning that high demands must be place on the leak …

Continue reading “Leak of valve type and test”

Fire Safe Ball Valve BH Series

BH series three-piece fire safe ball valves Fire safe ball valves applications API 607 and ISO 15848-1 certified.Patented stem packing design and seat design.Working temperature: -40°F to 400°F (-40°C to 204°C).Working pressure up to: 1500 psig (103 bar).Orifice size: 0.19″ (4.8 mm) to 1.25″ (31.8 mm).Helium leak rate/stem diameter ≤1.78×10-6 std cm3/s 1. Seal kit …

Continue reading “Fire Safe Ball Valve BH Series”

High Pressure Fittings How they work

High Pressure Fittings High Pressure Fittings Application High Pressure fittings product often said as Subsea fittings and Many Application in Deep sea equipment requires resistance with high pressure and resistant to corrosives caused sea water. High pressure valves usually have a pressure specification above 10000 psig until 60,000 psig. The High Pressure Fittings also many …

Continue reading “High Pressure Fittings How they work”

How to know specification of Excess Flow Valves

Excess Flow Valves Introduction If downstream line ruptures, the excess flow valve can stop uncontrolled release of system media. When the system is functioning normally, the working element remains in the open position. If the excess flow occurs downstream, the working element quickly moves to the tripped position to stop bleeding. When system pressure reaches balance …

Continue reading “How to know specification of Excess Flow Valves”

How to understand Metering Valve type

Metering Valve MS, MV, ML and MH Series MS Series Metering Valve Maximum working pressure: 2000 psig (138 bar) Working temperature: -10°F to 400°F (-23°C to 204°C) Orifice size: 0.032″ (0.81 mm) Flow coefficient (Cv): 0.004 Stem taper: 1° Turns to open: 9 to 12 Shutoff service: not available Panel mountable Flow patterns: straight, angle, cross and double Handle types: round, vernier, slotted and …

Continue reading “How to understand Metering Valve type”

Plug Valve

Plug Valve PV Series Plug Valve◎ Working pressure up to 3000 psig (207 bar)◎ Working temperature: -10 F to 400 F (-23 C to 204 C)◎ Size from 1/8 to 1/2 and 6 to 12 mm◎ Orifice sizes : 2.4 mm, 4.4 mm, 7.2 mm◎ Body materials: 316 SS, 304 SS, and brass◎ Seal materials …

Continue reading “Plug Valve”

Check Valve

Previous slide Next slide Check Valve CV Series Check Valve : Poppet Type Check valve Resilient O-ring seat design for leak free sealing.Working pressure up to: 3000 psig (207 bar) Working temperature: -10°F to 375°F (-23°C to 190°C) Cracking pressure: 1/3 to 25 psig (0.02 to 1.7 bar) COA Series Check Valve : One pieces Body Adjustable Compact, …

Continue reading “Check Valve”

Stainless Steel Needle Valve

Stainless Steel Needle Valves A Stainless Steel needle valve, as shown in Figure 1, is used to make relatively fine adjustments in the amount of fluid flow. The distinguishing characteristic of a needle valve is the long, tapered, needle like point on the end of the valve stem. This “needle” acts as a disk. The …

Continue reading “Stainless Steel Needle Valve”

How to find Gauge Valve Feature and Application

Gauge Valve • GV, GR up to 6000 psig (414 bar) • GVH up to 10000 psig (690 bar) GR Series Plug Tip Gauge Valve Lagging Extension 6000 psig GV Series Ball Tip Gauge 6000 psig GV Series Ball Tip Gauge Valve Lagging Extension 6000 psig GVH Series Ball Tip Gauge Valve 10000 psig GVH …

Continue reading “How to find Gauge Valve Feature and Application”